Command-Line Printing and Options

CUPS provides both the System V (lp(1)) and Berkeley (lpr(1)) printing commands for printing files. In addition, it supported a large number of standard and printer-specific options that allow you to control how and where files are printed.

## Printing Files

CUPS understands many different types of files directly, including text, PostScript, PDF, and image files. This allows you to print from inside your applications or at the command-line, whichever is most convenient! Type either of the following commands to print a file to the default (or only) printer on the system:

    lp filename
    lpr filename

### Choosing a Printer

Many systems will have more than one printer available to the user. These printers can be attached to the local system via a parallel, serial, or USB port, or available over the network. Use the lpstat(1) command to see a list of available printers:

    lpstat -p -d

The `-p` option specifies that you want to see a list of printers, and the `-d` option reports the current default printer or class.

Use the `-d` option with the lp command to print to a specific printer:

    lp -d printer filename

or the `-P` option with the lpr command:

    lpr -P printer filename

### Setting the Default Printer

If you normally use a particular printer, you can tell CUPS to use it by default using the lpoptions(1) command:

    lpoptions -d printer

### Printing the Output of a Program

Both the lp and lpr commands support printing from the standard input:

    program | lp
    program | lp -d printer
    program | lpr
    program | lpr -P printer

If the program does not provide any output, then nothing will be queued for printing.

### Specifying Printer Options

For many types of files, the default printer options may be sufficient for your needs. However, there may be times when you need to change the options for a particular file you are printing.

The lp and lpr commands allow you to pass printer options using the `-o` option:

    lp -o landscape -o scaling=75 -o media=A4 filename.jpg
    lpr -o landscape -o scaling=75 -o media=A4 filename.jpg

The available printer options vary depending on the printer. The standard options are described in the "Standard Printing Options" section below. Printer-specific options are also available and can be listed using the lpoptions command:

    lpoptions -p printer -l

### Creating Saved Options

Saved options are supported in CUPS through printer instances. Printer instances are, as their name implies, copies of a printer that have certain options associated with them. Use the lpoptions command to create a printer instance:

    lpoptions -p printer/instance -o name=value ...

The `-p printer/instance` option provides the name of the instance, which is always the printer name, a slash, and the instance name which can contain any printable characters except space and slash. The remaining options are then associated with the instance instead of the main queue. For example, the following command creates a duplex instance of the LaserJet queue:

    lpoptions -p LaserJet/duplex -o sides=two-sided-long-edge

Instances do not inherit lpoptions from the main queue.

### Printing Multiple Copies

Both the lp and lpr commands have options for printing more than one copy of a file:

    lp -n num-copies filename
    lpr -#num-copies filename

Copies are normally not collated for you. Use the `-o Collate=True` option to get collated copies:

    lp -n num-copies -o Collate=True filename
    lpr -#num-copies -o Collate=True filename

## Canceling a Print Job

The cancel(1) and lprm(1) commands cancel a print job:

    cancel job-id
    lprm job-id

The job-id is the number that was reported to you by the lp command. You can also get the job ID using the lpq(1) or lpstat commands:

    lpq
    lpstat

## Moving a Print Job

The lpmove(8) command moves a print job to a new printer or class:

    lpmove job-id destination

The job-id is the number that was reported to you by the lp or lpstat commands. Destination is the name of a printer or class that you want to actually print the job.

> Note:

> The lpmove command is located in the system command directory (typically /usr/sbin or /usr/local/sbin), and so may not be in your command path. Specify the full path to the command if you get a "command not found" error, for example:

>     /usr/sbin/lpmove foo-123 bar

## Standard Printing Options

The following options apply when printing all types of files.

### Selecting the Media Size, Type, and Source

The `-o media=xyz` option sets the media size, type, and/or source:

    lp -o media=Letter filename
    lp -o media=Letter,MultiPurpose filename
    lpr -o media=Letter,Transparency filename
    lpr -o media=Letter,MultiPurpose,Transparency filename

The available media sizes, types, and sources depend on the printer, but most support the following options (case is not significant):

- `Letter` - US Letter (8.5x11 inches, or 216x279mm)
- `Legal` - US Legal (8.5x14 inches, or 216x356mm)
- `A4` - ISO A4 (8.27x11.69 inches, or 210x297mm)
- `COM10` - US #10 Envelope (9.5x4.125 inches, or 241x105mm)
- `DL` - ISO DL Envelope (8.66x4.33 inches, or 220x110mm)
- `Transparency` - Transparency media type or source
- `Upper` - Upper paper tray
- `Lower` - Lower paper tray
- `MultiPurpose` - Multi-purpose paper tray
- `LargeCapacity` - Large capacity paper tray

The actual options supported are defined in the printer's PPD file in the `PageSize`, `InputSlot`, and `MediaType` options. You can list them using the lpoptions(1) command:

    lpoptions -p printer -l

When `Custom` is listed for the `PageSize` option, you can specify custom media sizes using one of the following forms:

    lp -o media=Custom.WIDTHxLENGTH filename
    lp -o media=Custom.WIDTHxLENGTHin filename
    lp -o media=Custom.WIDTHxLENGTHcm filename
    lp -o media=Custom.WIDTHxLENGTHmm filename

where "WIDTH" and "LENGTH" are the width and length of the media in points, inches, centimeters, or millimeters, respectively.

### Setting the Orientation

The `-o landscape` option will rotate the page 90 degrees to print in landscape orientation:

    lp -o landscape filename
    lpr -o landscape filename

The `-o orientation-requested=N` option rotates the page depending on the value of N:

- `-o orientation-requested=3` - portrait orientation (no rotation)
- `-o orientation-requested=4` - landscape orientation (90 degrees)
- `-o orientation-requested=5` - reverse landscape or seascape orientation (270 degrees)
- `-o orientation-requested=6` - reverse portrait or upside-down orientation (180 degrees)

### Printing On Both Sides of the Paper

The `-o sides=two-sided-short-edge` and `-o sides=two-sided-long-edge` options will enable two-sided printing on the printer if the printer supports it. The `-o sides=two-sided-short-edge` option is suitable for landscape pages, while the `-o sides=two-sided-long-edge` option is suitable for portrait pages:

    lp -o sides=two-sided-short-edge filename
    lp -o sides=two-sided-long-edge filename
    lpr -o sides=two-sided-long-edge filename

The default is to print single-sided:

    lp -o sides=one-sided filename
    lpr -o sides=one-sided filename

### Selecting the Banner Page(s)

The `-o jobsheets=start,end` option sets the banner page(s) to use for a job:

    lp -o job-sheets=none filename
    lp -o job-sheets=standard filename
    lpr -o job-sheets=classified,classified filename

If only one banner file is specified, it will be printed before the files in the job. If a second banner file is specified, it is printed after the files in the job.

The available banner pages depend on the local system configuration; CUPS includes the following banner files:

- `none` - Do not produce a banner page.
- `classified` - A banner page with a "classified" label at the top and bottom.
- `confidential` - A banner page with a "confidential" label at the top and bottom.
- `secret` - A banner page with a "secret" label at the top and bottom.
- `standard` - A banner page with no label at the top and bottom.
- `topsecret` - A banner page with a "top secret" label at the top and bottom.
- `unclassified` - A banner page with an "unclassified" label at the top and bottom.

### Holding Jobs for Later Printing

The `-o job-hold-until=when` option tells CUPS to delay printing until the "when" time, which can be one of the following:

- `-o job-hold-until=indefinite`; print only after released by the user or an administrator
- `-o job-hold-until=day-time`; print from 6am to 6pm local time
- `-o job-hold-until=night`; print from 6pm to 6am local time
- `-o job-hold-until=second-shift`; print from 4pm to 12am local time
- `-o job-hold-until=third-shift`; print from 12am to 8am local time
- `-o job-hold-until=weekend`; print on Saturday or Sunday
- `-o job-hold-until=HH:MM`; print at the specified UTC time

### Releasing Held Jobs

Aside from the web interface, you can use the lp command to release a held job:

    lp -i job-id -H resume

where "job-id" is the job ID reported by the lpstat command.

### Setting the Job Priority

The `-o job-priority=NNN` option tells CUPS to assign a priority to your job from 1 (lowest) to 100 (highest), which influences where the job appears in the print queue. Higher priority jobs are printed before lower priority jobs, however submitting a new job with a high priority will not interrupt an

### Specifying the Output Order

The `-o outputorder=normal` and `-o outputorder=reverse` options specify the order of the pages. Normal order prints page 1 first, page 2 second, and so forth. Reverse order prints page 1 last.

### Selecting a Range of Pages

The `-o page-ranges=pages` option selects a range of pages for printing:

    lp -o page-ranges=1 filename
    lp -o page-ranges=1-4 filename
    lp -o page-ranges=1-4,7,9-12 filename
    lpr -o page-ranges=1-4,7,9-12 filename

As shown above, the `pages` value can be a single page, a range of pages, or a collection of page numbers and ranges separated by commas. The pages will always be printed in ascending order, regardless of the order of the pages in the `page-ranges` option.

The default is to print all pages.

> Note:

> The page numbers used by `page-ranges` refer to the output pages and not the document's page numbers. Options like `number-up` can make the output page numbering not match the document page numbers.

### Selecting Even or Odd Pages

Use the `-o page-set=set` option to select the even or odd pages:

    lp -o page-set=odd filename
    lp -o page-set=even filename
    lpr -o page-set=even filename

The default is to print all pages.

### N-Up Printing

The `-o number-up=value` option selects N-Up printing. N-Up printing places multiple document pages on a single printed page. CUPS supports 1, 2, 4, 6, 9, and 16-Up formats; the default format is 1-Up:

    lp -o number-up=1 filename
    lp -o number-up=2 filename
    lp -o number-up=4 filename
    lpr -o number-up=16 filename

The `-o page-border=value` option chooses the border to draw around each page:

- `-o page-border=double`; draw two hairline borders around each page
- `-o page-border=double-thick`; draw two 1pt borders around each page
- `-o page-border=none`; do not draw a border (default)
- `-o page-border=single`; draw one hairline border around each page
- `-o page-border=single-thick`; draw one 1pt border around each page

The `-o number-up-layout=value` option chooses the layout of the pages on each output page:

- `-o number-up-layout=btlr`; Bottom to top, left to right
- `-o number-up-layout=btrl`; Bottom to top, right to left
- `-o number-up-layout=lrbt`; Left to right, bottom to top
- `-o number-up-layout=lrtb`; Left to right, top to bottom (default)
- `-o number-up-layout=rlbt`; Right to left, bottom to top
- `-o number-up-layout=rltb`; Right to left, top to bottom
- `-o number-up-layout=tblr`; Top to bottom, left to right
- `-o number-up-layout=tbrl`; Top to bottom, right to left

### Scaling to Fit

The `-o fitplot` option specifies that the document should be scaled to fit on the page:

    lp -o fitplot filename
    lpr -o fitplot filename

The default is to use the size specified in the file.

> Note:

> This feature depends upon an accurate size in the print file. If no size is given in the file, the page may be scaled incorrectly!

### Printing in Reverse Order

The `-o outputorder=reverse` option will print the pages in reverse order:

    lp -o outputorder=reverse filename
    lpr -o outputorder=reverse filename

Similarly, the `-o outputorder=normal` option will print starting with page 1:

    lp -o outputorder=normal filename
    lpr -o outputorder=normal filename

The default is `-o outputorder=normal` for printers that print face down and `-o outputorder=reverse` for printers that print face up.

### Printing Mirrored Pages

The `-o mirror` option flips each page along the vertical access to produce a mirrored image:

    lp -o mirror filename
    lpr -o mirror filename

This is typically used when printing on T-shirt transfer media or sometimes on transparencies.

### Raw or Unfiltered Output

The `-o raw` option allows you to send files directly to a printer without filtering. This is sometimes required when printing from applications that provide their own "printer drivers" for your printer:

    lp -o raw filename
    lpr -o raw filename

The `-l` option can also be used with the lpr command to send files directly to a printer:

    lpr -l filename

## Text Options

CUPS supports several options that are only used when printing plain text files. These options have absolutely no effect on PostScript, PDF, HP-GL/2, or image files.

### Setting the Number of Characters Per Inch

The `-o cpi=value` option sets the number of characters per inch:

    lp -o cpi=10 filename
    lp -o cpi=12 filename
    lpr -o cpi=17 filename

The default characters per inch is 10.

### Setting the Number of Lines Per Inch

The `-o lpi=value` option sets the number of lines per inch:

    lp -o lpi=6 filename
    lpr -o lpi=8 filename

The default lines per inch is 6.

### Setting the Number of Columns

The `-o columns=value` option sets the number of text columns:

    lp -o columns=2 filename
    lpr -o columns=3 filename

The default number of columns is 1.

### Setting the Page Margins

Normally the page margins are set to the hard limits of the printer. Use the `-o page-left=value`, `-o page-right=value`, `-o page-top=value`, and `-o page-bottom=value` options to adjust the page margins:

    lp -o page-left=value filename
    lp -o page-right=value filename
    lp -o page-top=value filename
    lp -o page-bottom=value filename
    lpr -o page-left=value -o page-right=value -o page-top=value -o page-bottom=value filename

The `value` argument is the margin in points; each point is 1/72 inch or 0.35mm.

### Pretty Printing

The `-o prettyprint` option puts a header at the top of each page with the page number, job title (usually the filename), and the date. Also, C and C++ keywords are highlighted, and comment lines are italicized:

    lp -o prettyprint filename
    lpr -o prettyprint filename

### Turning Off Text Wrapping

###

The `-o nowrap` option disables wrapping of long lines:

    lp -o nowrap filename
    lpr -o nowrap filename

## Not Supported on Mac OS XImage Options

CUPS supports several options that are only used when printing image files. These options have absolutely no effect on PostScript, PDF, HP-GL/2, or text files.

### Positioning Images

The `-o position=name` option specifies the position of the image on the page:

- `center` - Center the image on the page (default)
- `top` - Print the image centered at the top of the page
- `left` - Print the image centered on the left of page
- `right` - Print the image centered on the right of the page
- `top-left` - Print the image at the top left corner of the page
- `top-right` - Print the image at the top right corner of the page
- `bottom` - Print the image centered at the bottom of the page
- `bottom-left` - Print the image at the bottom left corner of the page
- `bottom-right` - Print the image at the bottom right corner of the page

### Scaling Images

The `-o scaling=percent`, `-o ppi=value`, and `-o natural-scaling=percent` options change the size of a printed image:

    lp -o scaling=percent filename
    lp -o ppi=value filename
    lpr -o natural-scaling=percent filename

The `scaling=percent` value is a number from 1 to 800 specifying the size in relation to the page (not the image.) A scaling of 100 percent will fill the page as completely as the image aspect ratio allows. A scaling of 200 percent will print on up to 4 pages.

The `ppi=value` value is a number from 1 to 1200 specifying the resolution of the image in pixels per inch. An image that is 3000x2400 pixels will print 10x8 inches at 300 pixels per inch, for example. If the specified resolution makes the image larger than the page, multiple pages will be printed to satisfy the request.

The `natural-scaling=percent` value is a number from 1 to 800 specifying the size in relation to the natural image size. A scaling of 100 percent will print the image at its natural size, while a scaling of 50 percent will print the image at half its natural size. If the specified scaling makes the image larger than the page, multiple pages will be printed to satisfy the request.

### Adjusting Image Hue (Tint)

The `-o hue=value` option will adjust the hue of the printed image, much like the tint control on your television:

    lp -o hue=value filename
    lpr -o hue=value filename

The `value` argument is a number from -360 to 360 and represents the color hue rotation. The following table summarizes the change you'll see with different colors:

Original | hue=-45 | hue=45
--- | --- | ---
Red | Purple | Yellow-orange
Green | Yellow-green | Blue-green
Yellow | Orange | Green-yellow
Blue | Sky-blue | Purple
Magenta | Indigo | Crimson
Cyan | Blue-green | Light-navy-blue

The default hue adjustment is 0.

### Adjusting Image Saturation (Color)

The `-o saturation=percent` option adjusts the saturation of the colors in an image, much like the color control on your television:

    lp -o saturation=percent filename
    lpr -o saturation=percent filename

The `percent` argument specifies the color saturation from 0 to 200. A color saturation of 0 produces a black-and-white print, while a value of 200 will make the colors extremely intense.

The default saturation is 100.

## HP-GL/2 Options

CUPS supports several options that are only used when printing HP-GL/2 files. These options have absolutely no effect on PostScript, PDF, image, or text files.

### Printing in Black

The `-o blackplot` option specifies that all pens should plot in black:

    lp -o blackplot filename
    lpr -o blackplot filename

The default is to use the colors defined in the plot file or the standard pen colors defined in the HP-GL/2 reference manual from Hewlett Packard.

### Setting the Default Pen Width

The `-o penwidth=value` option specifies the default pen width for HP-GL/2 files:

    lp -o penwidth=value filename
    lpr -o penwidth=value filename

The pen width `value` specifies the pen width in micrometers. The default value of 1000 produces lines that are 1 millimeter in width. Specifying a pen width of 0 produces lines that are exactly 1 pixel wide.

> Note:

> This option is ignored when the pen widths are set in the plot file.