HCCONTROL(8)            OpenBSD System Manager's Manual           HCCONTROL(8)

NAME
     hccontrol - Bluetooth HCI control utility

SYNOPSIS
     hccontrol [-hN] -n interface command [parameters ...]

DESCRIPTION
     The hccontrol utility sends specified command to the Bluetooth network
     interface.  The hccontrol utility will print results to the standard out-
     put and error messages to the standard error.

     The options are as follows:

     -h      Display usage message and exit.

     -N      Show Bluetooth addresses as numbers.  Normally hccontrol attempts
             to resolve Bluetooth addresses, and display them symbolically.

     -n interface
             Use specified network interface, e.g. ubt0.

     command
             One of the supported commands (see below).  Special command help
             can be used to obtain the list of all supported commands.  To get
             more information about specific command use help command.

     parameters
             One or more optional space separated command parameters.  Many
             commands require remote device address as one of the parameters.
             The remote device address can be specified as BD_ADDR or name.
             If name was specified then the hccontrol utility will attempt to
             resolve the name via bt_gethostbyname(3).

COMMANDS
     The currently supported HCI commands in hccontrol are:

     Inquiry
     Create_Connection
     Disconnect
     Add_SCO_Connection
     Change_Connection_Packet_Type
     Remote_Name_Request
     Read_Remote_Supported_Features
     Read_Remote_Version_Information
     Read_Clock_Offset
     Role_Discovery
     Switch_Role
     Read_Link_Policy_Settings
     Write_Link_Policy_Settings
     Reset
     Read_Pin_Type
     Write_Pin_Type
     Read_Stored_Link_Key
     Write_Stored_Link_Key
     Delete_Stored_Link_Key
     Change_Local_Name
     Read_Local_Name
     Read_Connection_Accept_Timeout
     Write_Connection_Accept_Timeout
     Read_Page_Timeout
     Write_Page_Timeout
     Read_Scan_Enable
     Write_Scan_Enable
     Read_Page_Scan_Activity
     Write_Page_Scan_Activity
     Read_Inquiry_Scan_Activity
     Write_Inquiry_Scan_Activity
     Read_Authentication_Enable
     Write_Authentication_Enable
     Read_Encryption_Mode
     Write_Encryption_Mode
     Read_Class_Of_Device
     Write_Class_Of_Device
     Read_Voice_Settings
     Write_Voice_Settings
     Read_Number_Broadcast_Retransmissions
     Write_Number_Broadcast_Retransmissions
     Read_Hold_Mode_Activity
     Write_Hold_Mode_Activity
     Read_SCO_Flow_Control_Enable
     Write_SCO_Flow_Control_Enable
     Read_Link_Supervision_Timeout
     Write_Link_Supervision_Timeout
     Read_Page_Scan_Period_Mode
     Write_Page_Scan_Period_Mode
     Read_Page_Scan_Mode
     Write_Page_Scan_Mode
     Read_Local_Version_Information
     Read_Local_Supported_Features
     Read_Buffer_Size
     Read_Country_Code
     Read_BD_ADDR
     Read_Failed_Contact_Counter
     Reset_Failed_Contact_Counter
     Get_Link_Quality
     Read_RSSI

     The currently supported node commands in hccontrol are:

     Read_Node_State
     Initialize
     Read_Debug_Level
     Write_Debug_Level
     Read_Node_Buffer_Size
     Read_Node_BD_ADDR
     Read_Node_Features
     Read_Node_Stat
     Reset_Node_Stat
     Flush_Neighbor_Cache
     Read_Neighbor_Cache
     Read_Connection_List
     Read_Node_Link_Policy_Settings_Mask
     Write_Node_Link_Policy_Settings_Mask
     Read_Node_Packet_Mask
     Write_Node_Packet_Mask
     Read_Node_Role_Switch
     Write_Node_Role_Switch

EXIT STATUS
     The hccontrol utility exits 0 on success, and >0 if an error occurs.

SEE ALSO
     bluetooth(3), ubt(4), hcseriald(8)

AUTHORS
     Maksim Yevmenkin <m_evmenkin@yahoo.com>

BUGS
     Most likely.  Please report if found.

OpenBSD 4.1                      June 14, 2002                               2
